Tableware: Head gasket

I had find many products about asbestos gasket sheet from some websites such as

	Car Seat Cushions & Covers Our Product lines include: Auto Interior Accessories: Car seat covers & cushions, Car waist cushions &..
	High Pressure Plastic Laminated Sheets - High Pressure Plastic Laminates sheets(HPL), double sides(both sides plain, both sides design, one..

And you can see more from king size comforter material safety sheet goose down duvets Corrugated Roofing Sheet winter horse blanket muscle pain relief chenille jacquard comforter little giraffe blanket neck rest pillow

Different kinds of gaskets, #4 indicating a V4 head gasket.

A replacement head gasket sitting loosely on top of a four cylinder engine block. Once positioned correctly the cylinder head will be bolted down on top of it.
A head gasket is a gasket that sits between the engine block and cylinder head in an internal combustion engine. Its purpose is to seal the cylinders to ensure maximum compression and avoid leakage of coolant or engine oil into the cylinders; as such, it is the most critical sealing application in any engine, and, as part of the combustion chamber, it shares the same strength requirements as other combustion chamber components.[1]
Contents
1 Head gasket types
2 Gasket problems
3 References
4 External links
//
Head gasket types
MLS - stands for "Multiple Layers Steel,". Most modern head engines are produced with MLS gaskets. These typically consist of three layers of steel.
The contact faces are usually coated with a rubber-like coating such as Viton that adheres to the cylinder block and cylinder head respectively whilst the thicker center layer is bare.
Solid copper - A solid sheet of copper, and typically requires special machining called 'o-ringing' that places a piece of wire around the circumference of the cylinder to bite into the copper. When this is performed copper gaskets are extremely durable. Recently companies have started producing copper gaskets with integral sealing wires permitting their retrofit into engines without the removal of the engine block for machine work.
Composite -- an older technology. Typically these are made from asbestos or graphite but are more prone to blowouts than newer gaskets. Asbestos gaskets are becoming increasingly rare due to health concerns.[2]
Elastomeric - a gasket type used by Rover on their K Series engines. It utilised a steel core plate with molded in place silicon rubber beads to seal oil and coolant passages. The bores were sealed by rolled steel fire rings in a more conventional manner. The idea behind the gasket design was to produce a production version of the technology used in F1 engines at the time. The original application of the gasket on the smaller versions of the K Series was very successful. However, an engine redesign resulted in persistent problems with the design - the joint interface became unstable and the gasket could not cope.
Gasket problems
Occasionally, the compression in the cylinder will cause a leak to form in the gasket and the gasket will have to be replaced, or severe damage can take place (a "blown" head gasket). This problem has been exacerbated by the use of aluminum rather than iron cylinder heads; while lighter than iron, aluminum has a much greater thermal expansion rate, which in turn causes a great deal more stress to be placed on the head gasket. Engine makers have responded to this by adding a non-stick coating such as Teflon to the surface of the head gasket.
If the gasket fails, a variety of problems can occur, from compression loss (leading to power reduction, or a rough engine), to exhaust gases being forced into the cooling system, leading to the engine overheating and increased engine wear due to the motor oil being mixed with antifreeze. Coolant can leak into the cylinders, causing the exhaust to issue steam[3] and the catalytic converter to be damaged. If a very large amount of coolant does this, hydrolock can occur, causing extensive engine damage. Sometimes, all that may happen when a head gasket is blown is excessive steam erupting from the tailpipe; yet the engine may act and drive like normal, until all the coolant is gone engine overheating results.

A damaged head gasket can cause compression to leak between cylinders.
Head gasket condition can be investigated by checking the compression pressure with a pressure gauge, or better, a leak-down test, and/or noting any indication of combustion gasses in the cooling system on a water-cooled engine. Oil mixed with coolant and excessive coolant loss with no apparent cause, or presence of carbon monoxide or hydrocarbon gases in the expansion tank of the cooling system can also be signs of head gasket problems.
Driving with a blown head gasket (if possible) can cause additional extensive damage due to overheating or loss of lubrication.
Blue exhaust smoke may be indicative of oil-burning.
References
^ Bickford, John H. (1997). Gaskets and Gasketed Joints. CRC Press. p.57. ISBN 0-824-798-775.
^ Nunney, M. J. (1998). Light & Heavy Vehicle Technology. Elsevier. p.23. ISBN 0-750-638-273. "Since exposure to asbestos is now recognized as being a health hazard [...] the manufacture of non-asbestos cylinder head gaskets has now become established."
^ Nunney, p. 23.
External links
Wikimedia Commons has media related to: head gaskets
...(and so on)